IPv6 Operations J. Massar Internet-Draft Unfix / SixXS Expires: December 27, 2004 June 28, 2004 AYIYA: Anything In Anything draft-massar-v6ops-ayiya-01 Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http:// www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on December 27, 2004. Copyright Notice Copyright (C) The Internet Society (2004). All Rights Reserved. Abstract This document defines a tunneling protocol that can be encapsulated in any other protocol. This protocol uses authentication tokens, allowing multiple identities to exist on the same endpoint and thus also to created tunnels from/to the same NAT and also making it possible to automatically change the endpoint of the tunnel. This protocol is intended as an alternative to the proto-41 protocol in use for tunneling IPv6 over IPv4 packets over the Internet but can also be applied in multihoming solutions. Due to the authentication this protocol is especially useful for dynamic non-24/7 endnodes which are located behind NATs and want to use a IPv6 Tunnel Broker, for instance. The protocol can carry any payload and thus is not limited to only IPv6 over IPv4 but can also be used for IPv4 over IPv6 and many other combinations of protocols. Massar Expires December 27, 2004 [Page 1] Internet-Draft AYIYA: Anything In Anything June 2004 Table of Contents 1. Requirements notation . . . . . . . . . . . . . . . . . . . . 3 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. AYIYA Packet Format . . . . . . . . . . . . . . . . . . . . . 4 3.1 Identity Length (IDLen) . . . . . . . . . . . . . . . . . 5 3.2 Identity Type (IDType) . . . . . . . . . . . . . . . . . . 5 3.3 Signature Length (SigLen) . . . . . . . . . . . . . . . . 5 3.4 Hashing Method (HshMeth) . . . . . . . . . . . . . . . . . 6 3.5 Authentication Method (AutMeth) . . . . . . . . . . . . . 6 3.6 Operation Code (OpCode) . . . . . . . . . . . . . . . . . 7 3.7 Next Header . . . . . . . . . . . . . . . . . . . . . . . 7 3.8 Epoch Time . . . . . . . . . . . . . . . . . . . . . . . . 7 4. AYIYA Heartbeat . . . . . . . . . . . . . . . . . . . . . . . 9 5. Signing the packet . . . . . . . . . . . . . . . . . . . . . . 9 5.1 Hashing the packet . . . . . . . . . . . . . . . . . . . . 10 5.2 Signing with a Shared Secret . . . . . . . . . . . . . . . 10 5.3 Signing with a Public/Private Key . . . . . . . . . . . . 10 6. Identity information in DNS . . . . . . . . . . . . . . . . . 11 7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 11 8. Security Considerations . . . . . . . . . . . . . . . . . . . 11 9. Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9.1 Using AYIYA for IPv6 Tunnel Brokers . . . . . . . . . . . 13 9.2 Tunneling to multiple endhosts behind a NAT . . . . . . . 14 9.3 Multihoming using AYIYA . . . . . . . . . . . . . . . . . 15 9.4 Mobility using AYIYA . . . . . . . . . . . . . . . . . . . 18 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . 18 11. References . . . . . . . . . . . . . . . . . . . . . . . . . 18 Author's Address . . . . . . . . . . . . . . . . . . . . . . . 20 Intellectual Property and Copyright Statements . . . . . . . . 21 Massar Expires December 27, 2004 [Page 2] Internet-Draft AYIYA: Anything In Anything June 2004 1. Requirements notation The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2. Introduction Many users are currently located behind NATs which prohibit the usage of proto-41 IPv6 in IPv4 tunnels [RFC3056] unless they manually reconfigure their NAT setup which in some cases is impossible as the NAT cannot be configured to forward proto-41 ([RFC1933]) to a specific host. There might also be cases when multiple endpoints are behind the same NAT, when multiple NATs are used or when the user has no control at all over the NAT setup. This is an undesired situation as it limits the deployment of IPv6 [RFC3513], which was meant to solve the problem of the disturbance in end to end communications caused by NATs, which where created because of limited address space in the first place. This problem can be solved easily by tunneling the IPv6 packets over either UDP [RFC0768], TCP [RFC0793] or even SCTP [RFC2960]. Taking into consideration that multiple separate endpoints could be behind the same NAT and/or that the public endpoint can change on the fly, there is also a need to identify the endpoint that certain packets are coming from and endpoints need to be able to change e.g. source addresses of the transporting protocol on the fly while still being identifiable as the same endpoint. The protocol described in this document is independent of the transport and payload's protocol. An examples could be IPv6-in-UDP-in-IPv4, which is a typical setup that can be used by IPv6 Tunnel Brokers [RFC3053]. This document does not describe how to determine the identity, signature type or the inner and outer protocols. These should be negotiated manually or automatically by e.g. using TSP or a relevant protocol which is capable of describing the configuration parameters of AYIYA tunnels. Seperate documents for the configuration protocols supporting AYIYA should include the details on how this is done. Additionally this document describes how AYIYA could be used in both a multihoming and in a mobility scenario. Massar Expires December 27, 2004 [Page 3] Internet-Draft AYIYA: Anything In Anything June 2004 3. AYIYA Packet Format The AYIYA protocol is put inside the data part of either UDP [RFC0768], TCP [RFC0793] or SCTP [RFC2960] which are the currently defined transport protocols, future transport protocols could also be used. The transport protocol can be run over both IPv4 or IPv6 or any other future protocol. Schematically, this will look like the following diagram. +--------+ +----------+ | Sender | <--- Internet ---> | Receiver | +--------+ +----------+ A complete on the wire packet will have the following format. +-------------------------------+ | Delivery Header | | IPv4/IPv6/... | +-------------------------------+ | Transport Header | | TCP/UDP/SCTP/... | +-------------------------------+ | AYIYA Header | +-------------------------------+ | Payload packet | +-------------------------------+ The AYIYA protocol has a header with the following format. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IDLen | IDType| SigLen|HshMeth|AutMeth| OpCode| Next Header | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Epoch Time | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Identity : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Signature : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ All fields are in network byte order (Big Endian). The base AYIYA header without an identity or signature is 8 bytes. Massar Expires December 27, 2004 [Page 4] Internet-Draft AYIYA: Anything In Anything June 2004 3.1 Identity Length (IDLen) The IDLen (Identity Length) Field defines the length of the Identity Field in a power of 2 in octets. e.g. a Lenght of 4 is 2^4 = 16 bytes. 3.2 Identity Type (IDType) The Identity Type specifies what kind of Identity is included in the header. The Idenity field is used by the receiver to determine which sender sent the packet, this is done as there is an assumption that the source endpoint, the source IP address or the source port, may change arbitrarily which will be the case when the sender is behind a NAT, using DHCP, PPP or using IPv6 privacy extensions [RFC3041] and thus has a changing address. Even though the endpoint is suspectible to change, the Identity will remain the same unless negotiated otherwise. Currently defined Identity types are: - 0x0 None - 0x1 Integer - 0x2 ASCII string Types 0x3 till 0xf are reserved for future usage. The type of identity used by an AYIYA tunnel is negotiated either manually or automatically outside this protocol, these fields are included to allow verification of the type and also to allow multiple types to be used by one receiver at the same time. ASCII strings are NULL padded when they do not fill the complete identity field. The types are multifunctional, e.g. type 0x01 could contain an IPv4 address when the length of the identity is 0x2 or could contain an IPv6 address when the length is 0x4. A string could contain DNS names. The exact content of the Identity Field is defined by the users of this protocol and out of scope of this document. If the Identity Type is None, the Identity Field is absent from the packet. The Signature Field, if present, will then directly follow the Epoch Time Field. In case the Signature Field is not present the payload will directly follow the Epoch Time field. The Identity Length Field must be 0 in this case. 3.3 Signature Length (SigLen) The SigLen describes the length of the hash and is specified in octets divided by four. e.g. a SigLen of 3 means the signature is 12 bytes long, a SigLen of 15 means that the Signature is 60 bytes long. The protocol thus allows for a maximum signature of 480 bits. Massar Expires December 27, 2004 [Page 5] Internet-Draft AYIYA: Anything In Anything June 2004 3.4 Hashing Method (HshMeth) The HshMeth (Hashing Method) bits describe the type of the Hashing Method used to create the signature of the packet. By hashing the complete packet we can verify that the packet did not change during transit between sender and receiver. Currently defined Hashing Methods are: - 0x0 No hash - 0x1 MD5 [RFC1321] - 0x2 SHA1 [RFC3174] As there are known collisions for MD5 it is advised to use SHA1 as a default Hashing Method. Hashing Methods 0x3 to 0xf are reserved for future usage. When the Hashing Method is 0x0, AuthMeth and SigLen MUST also be set to 0 and the packet doesn't include a Signature, the payload, defined by the Next Header, then directly follows the Identity field, which may also be absent depending on it's type. 3.5 Authentication Method (AutMeth) AuthMeth (Authentication Method) describes the type of the Authentication Method. By authenticating the packet we can verify that the sender really originated from the sender, of course assuming that the Authentication Method has not been compromised. The AYIYA protocol doesn't have any options for encryption. Encryption can be done in the payload. The currently defined Authentication Methods are: - 0x0 No authentication - 0x1 Hash using a Shared Secret - 0x2 Hash using a public/private key method Authentication Methods 0x3 to 0xf are reserved for future usage. In the case where an implementation does not support or expect the received Identity or Signature Type (e.g. because it was configured for a different type) it MUST silently discard the packet. The user may be notified of this event. Massar Expires December 27, 2004 [Page 6] Internet-Draft AYIYA: Anything In Anything June 2004 3.6 Operation Code (OpCode) The Operation Code can request special operation on the packet. Currently - 0x0 No Operation / Heartbeat - 0x1 Forward - 0x2 Echo Request - 0x3 Echo Request and Forward - 0x4 Echo Response The No Operation OpCode allows the packet to be used for updating the latest received time, see the next section for the rationale why this packet is also dubbed a Heartbeat Packet. The Forward OpCode specifies that this is a normal packet which is to be forwarded. The Echo Request OpCode requests that the payload is echoed back to the sender, the OpCode of the returned packet should then be set to Echo Response. The payload of the Echo Request packet MUST NOT be forwarded. When the OpCode is set to Echo Request and Forward then the packet must be echoed back to the sender and also forwarded as a normal packet. This allows the Heartbeat functionality, as discussed in the next chapter, to be integrated into the normal packet stream. It can also be used to ensure that a packet is delivered to the other end of the tunnel. Values 0x3 till 0xf are reserved for future extensions. 3.7 Next Header The Next Header, like in IPv6, contains the protocol value of the payload following the AYIYA Packet Header. There is no length field as that can be deduced from the protocol that is carrying this packet. 3.8 Epoch Time Epoch Time is the time in seconds since "00:00:00 1970-01-01 UTC". Both the sender and the receiver are advised to be synchronized using NTP [RFC2030] to make sure that their clocks clocks do not differ too much even after travelling the intermediate networks between the sender and the receiver. The number of seconds since the above date are stored in a 32 bit unsigned integer in network byte order. The Epoch Time is included to be able to guard against replay attacks. See the Security Considerations section for more details. Massar Expires December 27, 2004 [Page 7] Internet-Draft AYIYA: Anything In Anything June 2004 The Epoch Time will loop in 2038 when the 32 bit unsigned integer reaches it's maximum value. This will cause that the difference between the two times is larger than the advised timeout time even though the difference is not that big. To avoid a service interruption, because the time in the packet is not inside the limits of the clock shift time, every implementation MUST handle times in the range (0-timeout)..0 specially and compensate the loop, e.g. by shifting away from the looptime. Typical C code which handles the verification of the epochtime is included as an example: // epochtime = epochtime as received in the packet // Don't forget to convert the byteorder using ntohl() bool ayiya_checktime(time_t epochtime) { // Number of seconds we allow the clock to be off #define CLOCK_OFF 120 int i; // Get the current time time_t curr_time = time(NULL); // Is one of the times in the loop range? if ( (curr_time >= -CLOCK_OFF) || (epochtime >= -CLOCK_OFF)) { // Shift the times out of the loop range i = (curr_time + (CLOCK_OFF*2)) - (epochtime + (CLOCK_OFF*2)); } else i = curr_time - epochtime; // The clock may be faster, thus flip the sign if (i < 0) i = -i; // Compare the clock offset if (i > CLOCK_OFF) { // Time is off, silently drop the packet return false; } // Time is in the allowed range return true; } Theory for the above: for simplicity let's assume the loop is around 10000. Sender sends an epochtime of 9990, but the receiver's time is at 10 already, thus we apply the shift and the times become: (9990 + Massar Expires December 27, 2004 [Page 8] Internet-Draft AYIYA: Anything In Anything June 2004 240)%10000 = 230 and (10 + 240)%10000 = 250 the difference !(250 - 230) is 20, which is in the allowed clock_off range. If we didn't apply this compensation the difference would have been !(10 - 9990) = 9980 seconds which would mean the packet would have been dropped even though the packets time is valid. 4. AYIYA Heartbeat As the receiver will disable the tunnel after it has not received a packet from the sender after a configured time the sender should send packets to the other side of the tunnel with the Next Header field set to 59 (No Next Header) but the payload may contain data which is private to the implementation. The implementation could include a sequence number in the payload like is common with ICMP echo [RFC2463] packets. The receiver will reply on reception of this packet returning the exact payload the sender transmitted allowing the sender to compare the information and deduce latency information and other statistical information from it using the implementation specific data contained in the payload. This packet allows the sender to test the tunnel's functionality. If the signature is not correct, either because of the wrong shared secret, wrong hash, wrong identity or connectivity problems, the sender will not get a reply and could notify the user of this situation. Senders should send these packets once per 60 seconds as the receiver is usually configured to disable the tunnel after it has received no packets for a timeout time of 120 seconds. An implementation could choose to not send the heartbeat packet when it has already sent a packet in the last 60 seconds thus avoiding a small overhead in transmission and processing of these extra heartbeat packets. Receivers MUST handle every correctly verified packet as the last received one. A side effect of this Heartbeat Packet is that a NAT will update it's mappings and keep the same source/destination ports in cases where AYIYA is encapsulated inside UDP, for instance. An implementation could choose to not send any heartbeat packets, but this will cause the connecitivity, provided by the tunnel, to be interrupted until the sender sends a packt again. 5. Signing the packet When there is no Hashing there neither is no signing of the packet and the header won't include a Signature. If a received packet contains flags that the packet contains a hash or that the packet contains an authentication then the receiver must Massar Expires December 27, 2004 [Page 9] Internet-Draft AYIYA: Anything In Anything June 2004 verifiy that the signature provided is correct by following the same procedure as taken by the sender and comparing the results of the signatures. When the signatures match the packet can be processed further. When the signatures do not match the receiver MUST silently ignore the packet and may notify the user. 5.1 Hashing the packet When there is no Authentication we create the signature of the packet by initializing the signature of the packet to NULL. The rest of the fields and the payload should also be initialized as to be sent over the wire. The signature is then made over the complete packet using the Hashing Method defined by the type. Thus over the AYIYA header and the payload. This method allows verification that the packet has not been incidentally mangled along it's route to the receiver. It does not provide any security or authenticity that the packet has been forcefully mangled. 5.2 Signing with a Shared Secret To create the signature of the packet, the Signature Field MUST be set to the signature of the shared secret, this signature is made using the same hashing method as the one specified in the Signature Type Field. The signature is then made over the complete packet, thus the AYIYA header and the payload. By hashing the shared secret we allow shared secrets of arbitrary lengths to be used. Which shared secret is used is out of scope of this document and this should be described by manual or automatic configuration documents which should describe the definition of the shared secret. The result is stored in the Signature field, which contains the signature of the shared secret while hashing. Implementations could precache the hashed shared secret and would thus not require the knowlegde of the real shared secret. This method thus allows verification that the packet has not been modified along it's path from sender to receiver and also allows verification that the sender or receiver, who should be the only parties knowning the shared secrets, where the originators of this packet. This withouth sending the shared secret over the network. 5.3 Signing with a Public/Private Key The Signature Field of the header is initialized to NULL. The rest of the fields and the payload should also be initialized as to be sent Massar Expires December 27, 2004 [Page 10] Internet-Draft AYIYA: Anything In Anything June 2004 over the wire. A hash defined by the HshMeth Field is then calculated over the complete packet. After that the Public / Private Key signature is calculated, the result of which is stored in the Signature Field. 6. Identity information in DNS Some of the Identity Types could represent an IPv4 or IPv6 address or a hostname. Using normal (reverse) DNS lookup procedures the additional properties relating to these identities can then also be found out using DNS. These properties could be altnerate endpoint addresses, pointers to home agents or public keys. This can be used for the multihoming and mobility scenarios to bootstrap the initial connection. When a receiver receives the first packet from a, upto then unknown identity, it could lookup the identities additional properties like it's public key to be able to authenticate the received packet. 7. Acknowledgements The protocol presented has formed during the existence of SixXS [SIXXS] to allow the users of the various Tunnel Servers provisioned by SixXS to have a dynamic non-static IPv4 endpoint which could even be located behind a NAT. This protocol is the natural successor of the combination of the proto-41 tunneling protocol and the SixXS Heartbeat protocol. Thanks to Christian Strauf, Brian Carpenter and Pim van Pelt for valuable comments which improved this document and therefore the protocol a lot. 8. Security Considerations The shared secret used MUST never be made publicly available to 3rd parties otherwise that 3rd party could sign a packet and automatically reconfigure the tunnel endpoint. This would enable a 3rd party to send traffic in both directions and thus posing as the actual user. The inclusion of the Epoch Time along with the verification on the receiver side should guard against replay attacks. The receiver MUST ensure that the time difference between local clock and the epochtime never differ for more than 60 seconds. This allows for a tolerance of latency and time-shifts. Note that the Epoch Time doesn't guard against resending of the same packet. A solution could be to add a sequence number in the AYIYA protocol but that would overcomplicate the receivers as they would Massar Expires December 27, 2004 [Page 11] Internet-Draft AYIYA: Anything In Anything June 2004 need to keep state and even re-order packets, which is something that is not wanted with a protocol that is built to allow packets to drop. Upper layer protocols should have protection mechanisms against this. e.g. TCP has it's own sequence numbering. Any packet that is not well formed or contains a invalid signature MUST be silently dropped, appropriate logging may be done of these issues but in that case a rate limit MUST be applied to not clutter the logs with these messages. Invalid signatures MUST be handled as possibly being spoofed, thus no packet MUST be sent back as these packets would then go to the spoofed source address. As a side effect of this protocol, when a sender can not or does not send a packet in time, the tunnel is detected as defunct and the receiver will dispose of it. This could be the case when the sender's connectivity is interrupted. Disposition of the tunnel will also make sure that no packets will be forwarded over the tunnel to an endpoint which might not be expecting this kind of traffic as it is not the host that heartbeated the last time. This situation could arise for instance when DHCP changes the endpoint address or a host which dials into a PPP pool disconnects, after which the next dialin, by another host receives the former hosts endpoint address. This document specifies a tunneling protocol which can circumvent administrative policies implied by a firewall. This firewall can prohibit the communication between sender and reciever. If such a policy is in place, then that is an administrative policy which should not be tried to be circumvented. Using tunneling in general opens up a new hole into a network which might be used for gaining access into that network. When and one or both of the outer addresses is a [RFC3041] address, any process that receives the AYIYA packets can still make the relation to that single host as the Identity in the AYIYA packet doesn't change. The limited privacy effect of RFC3041 is thus removed in this case. 9. Scenarios As AYIYA is a generic tunneling protocol it can be used in many different scenario's amongst which the scenarios described in this section. Note that TEST-NET [RFC3300] addresses used in the scenarios could never reach a Tunnel Server over the public Internet due to filtering of these documentation prefixes. Massar Expires December 27, 2004 [Page 12] Internet-Draft AYIYA: Anything In Anything June 2004 9.1 Using AYIYA for IPv6 Tunnel Brokers The main scenario where AYIYA is intended to be used is for solving the problem where a IPv4 host is behind a NAT and wants to tunnel to a Tunnel Server [RFC3056]. As many NAT's don't support forwarding protocol 41 or require manual configuration of the NAT, using AYIYA and encapsulating the AYIYA packet including the payload inside IPv4 UPD is a good solution. The AYIYA packet includes an identity, thus the endpoint address of the client does not need to be known and the tunnel can be brought and kept up up at wish by the user when it's client notifies the Tunnel Server of it's existence by sending AYIYA packets. This type of tunnel will generally use a Identity Type of 0x3, the Identity Field will contain the IPv6 address of the endpoint of the tunnel from the direction where the packet is coming from, the Signature Type will be 0x2 (SHA-1). 192.0.2.2 192.0.2.1 2001:db8::2/64 2001:db8::1/64 +----------+ +--------+ | Tunnel |<----------->| Tunnel | | Client | | Server | +----------+ +--------+ The packet send over the wire will have the following format: +---------+ | IPv4 | +---------+ | UDP | +---------+ | AYIYA | +---------+ | IPv6 | +---------+ | Payload | +---------+ This setup causes a per-packet overhead of: 20 (IPv4) + 8 (UDP) + 8+16+20 (AYIYA+Identity+Signature) = 72 bytes. This allows encapsulation of packets of 1428 bytes over Ethernet, which has a MTU of 1500 bytes. As the minimum MTU of IPv6 packets is 1280 bytes, any medium with at least an MTU of (1280 + 72 =) 1352 bytes can be used for AYIYA without having to fragment the packets. Massar Expires December 27, 2004 [Page 13] Internet-Draft AYIYA: Anything In Anything June 2004 9.2 Tunneling to multiple endhosts behind a NAT This scenario demonstrates a typical situation where this protocol will mainly be used: tunneling to multiple endhosts behind a NAT. In this scenario the Tunnel Server acts as a receiver in server mode which does not initiate any tunneling as it does not know the source endpoint of the clients, which might change at arbitrary timepoints. In this scenario the server is assumed to have a static endpoint. The server does not send heartbeats to check connectivity, it is up to the client to send the heartbeats at the agreed regular intervals making sure the server does not dispose of the tunnel. This setup allows both clients behind the NAT to change their private IPv4 addresses and also allows the NAT to change its public IPv4 or source port numbers. The server will notice the changes of source IP or port numbers and can reconfigure its tunnel to send to the specific host:port combination for which a mapping will exist at the NAT and the packet can go through the NAT. 10.0.0.0/8 NAT 192.0.2.0/24 | +----------+ (1) | (2) +--------+ | Client A |------|------| | +----------+ | | Tunnel | +----------+ | | Server | | Client B |------|------| | +----------+ (3) | (4) +--------+ | (1) = src = 10.10.0.1:1234, dst = 192.0.2.42:3740 (2) = src = 192.0.2.5:4321, dst = 192.0.2.42:3740 (3) = src = 10.10.9.2:7890, dst = 192.0.2.42:3740 (4) = src = 192.0.2.5:5678, dst = 192.0.2.42:3740 AYIYA is capable of crossing any NAT. As an AYIYA Server uses the AYIYA port as the source port and the address that received the initial AYIYA packet from the client as a source address, Restricted Cone NATs, Port-Restricted Cone NATs and Symmetric NATs can be traversed. If the mapping would change the next packet coming from the client would update the host:port mapping on the Tunnel Server. The four main types of NAT's are described in the Teredo document. Massar Expires December 27, 2004 [Page 14] Internet-Draft AYIYA: Anything In Anything June 2004 This scenario would typically encapsulate AYIYA and the payload inside IPv4 and UDP. Schematically this would look like: +---------+ | IPv4 | +---------+ | UDP | +---------+ | AYIYA | +---------+ | Payload | +---------+ 9.3 Multihoming using AYIYA AYIYA can also be used as a tunneling protocol for solving multihoming problems. For instance the following packet could be crafted which encapsulates IPv6 inside IPv6. The encapsulated packet could contain a source/destination address which could be described as the identifiers of this multihoming protocol. The outer IPv6 addresses are the locators. Massar Expires December 27, 2004 [Page 15] Internet-Draft AYIYA: Anything In Anything June 2004 A typical Multihoming scenario. Site A is connected to the Internet using two independent upstream providers (Provider 1 and Provider 2). Every host inside Site A has two addresses, one from Provider 1 (2001:db8:1000::/48) and one from Provider 2 (2001:db8:2000::/48). Both upstream providers correctly filter egress traffic making sure that only source addresses assigned to Site A from their own address space is sent to the Internet, thus protecting against spoofing. The SiteRouters must thus make sure that only the correctly sourced packets are sent outward. Either the Host or the SiteRouters could support AYIYA, in the first case the SiteRouters MUST never do any additional AYIYA tunneling, this can be accomplished easily by checking that the IPv6 Next Header or IPv4 Protocol field doesn't contain the value mentioning that the next header is an AYIYA header. If this value is not set to be an AYIYA header, the SiteRouters MAY initiate AYIYA traffic to the remote host or site using their Site Identifiers. This allows host-host, host-site and also site-site multihoming. +---------------------------------------+ | +------------+ Site A | | | Host A | | | +------------+ | | | | | | | | | | +--------------+ +--------------+ | | | SiteRouter 1 | | SiteRouter 2 | | | +--------------+ +--------------+ | | | | | +--------|--------------------|---------+ | | +--------------+ +--------------+ | Provider 1 | | Provider 2 | +--------------+ +--------------+ | | | | +------------------------------------+ | The Internet | +------------------------------------+ | +------------+ | Host B | +------------+ The hosts communicating with each other using this setup would need to agree on which identities, hashing, authentication methods and shared secrets or private/public keys they use. This is out of scope for this document. Massar Expires December 27, 2004 [Page 16] Internet-Draft AYIYA: Anything In Anything June 2004 The following figure depicts an example IPv6 TCP packet which is encapsulated using AYIYA inside IPv4 or IPv6 which demonstrates its protocol independency. The Next Header field of the outer IPv6 packet directly contains a IPv6 Next Header value of IANA:TBD. The Next Header field of the AYIYA Header contains the value of 41 (IPv6). The locators used are IPv4 or IPv6 addresses, while the identifiers and the actual protocol addresses that are being multihomed are IPv6. This scenario could allow a host to decide to start communicating with another host over IPv4 when an IPv6 route is not available or doesn't have the required properties, based on latency for instance. +---------+ |IPv4/IPv6| +---------+ | AYIYA | +---------+ | IPv6 | +---------+ | TCP | +---------+ | Payload | +---------+ If the locator of a host changes, that host can directly send a heartbeat packet to the other host notifying that host of the change. The receiving host recognises the new locator as a valid source as the signature can be verified and sets it's outgoing packets to use this new endpoint. As the identifiers are encapsulated, existing connections or communications won't notice this change. Massar Expires December 27, 2004 [Page 17] Internet-Draft AYIYA: Anything In Anything June 2004 9.4 Mobility using AYIYA AYIYA could be used in a mobility situation for tunneling it's Home Address back to the Home Agent, thus acting as a normal tunnel situation and for the Remote Host it seems the communication is happening directly. In this case the remote host doesn't need to support AYIYA. When the Remote Host does support AYIYA, it could also directly setup a tunnel with the mobile host, circumventing that traffic is sent over the Home Agent. The Remote Host can determine if a host supports AYIYA by looking up properties in DNS and use a Public/Private Key algorithm to authenticate the packets without prior information, e.g. the keys, needing to be available. The following diagram illustrates this. +-------------+ +------------+ | Mobile Host |<--AYIYA-->| Home Agent | +-------------+ +------------+ ^ ^ | | AYIYA IPv4/IPv6 | | v v +-------------+ +-------------+ | Remote Host | | Remote Host | | + AYIYA | | | +-------------+ +-------------+ The exact mechanism for determining the public/private key and the identities used are out of scope for this document. 10. IANA Considerations IANA will need to allocate a protocol number value for "AYIYA" allowing AYIYA packets to be directly encapsulated inside IPv4, IPv6 or possibly any other future protocols. IANA will need to allocate a port number in the case where AYIYA is used over UDP [RFC0768], TCP [RFC0793] or SCTP [RFC2960] or any other protocol supporting port numbers. A port number request has been made through normal port allocation procedures requesting a system port. 11 References [RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768, August 1980. [RFC0793] Postel, J., "Transmission Control Protocol", STD 7, RFC 793, September 1981. Massar Expires December 27, 2004 [Page 18] Internet-Draft AYIYA: Anything In Anything June 2004 [RFC1321] Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321, April 1992. [RFC1933] Gilligan, R. and E. Nordmark, "Transition Mechanisms for IPv6 Hosts and Routers", RFC 1933, April 1996. [RFC2030] Mills, D., "Simple Network Time Protocol (SNTP) Version 4 for IPv4, IPv6 and OSI", RFC 2030, October 1996. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2463] Conta, A. and S. Deering, "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification", RFC 2463, December 1998. [RFC2960] Stewart, R., Xie, Q., Morneault, K., Sharp, C., Schwarzbauer, H., Taylor, T., Rytina, I., Kalla, M., Zhang, L. and V. Paxson, "Stream Control Transmission Protocol", RFC 2960, October 2000. [RFC3041] Narten, T. and R. Draves, "Privacy Extensions for Stateless Address Autoconfiguration in IPv6", RFC 3041, January 2001. [RFC3053] Durand, A., Fasano, P., Guardini, I. and D. Lento, "IPv6 Tunnel Broker", RFC 3053, January 2001. [RFC3056] Carpenter, B. and K. Moore, "Connection of IPv6 Domains via IPv4 Clouds", RFC 3056, February 2001. [RFC3174] Eastlake, D. and P. Jones, "US Secure Hash Algorithm 1 (SHA1)", RFC 3174, September 2001. [RFC3300] Reynolds, J., Braden, R., Ginoza, S. and A. De La Cruz, "Internet Official Protocol Standards", RFC 3300, November 2002. [RFC3513] Hinden, R. and S. Deering, "Internet Protocol Version 6 (IPv6) Addressing Architecture", RFC 3513, April 2003. [SIXXS] Massar, J. and P. van Pelt, "SixXS - IPv6 Deployment & Tunnelbroker", . Massar Expires December 27, 2004 [Page 19] Internet-Draft AYIYA: Anything In Anything June 2004 Author's Address Jeroen Massar Unfix / SixXS Hofpoldersingel 45 Gouda 2807 LW NL EMail: jeroen@unfix.org URI: http://unfix.org/~jeroen/ Massar Expires December 27, 2004 [Page 20] Internet-Draft AYIYA: Anything In Anything June 2004 Intellectual Property Statement The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. Full Copyright Statement Copyright (C) The Internet Society (2004). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assignees. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION Massar Expires December 27, 2004 [Page 21] Internet-Draft AYIYA: Anything In Anything June 2004 HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgment Funding for the RFC Editor function is currently provided by the Internet Society. Massar Expires December 27, 2004 [Page 22]